NEW release from Gate for April 2016!
The V1.1 has the latest firmware upgrades, offering better trigger response when using the Auto pre-cock feature.
See it in action here.
The WARFET is GATE's latest offering with 20 functions, and over 6 million possible configurations, all programmable via an auxiliary Tactical Programming Card which you just plug in between the battery and AEG control unit. When you're done programming, just unplug the card and you're all set.
New features not found in previous Gate Mosfets include programmable Pre-cocking , 1-5 round burst options, Dark Mode, and convenient wire adaptors are now included with the WARFET kit
VIEW GATE MOSFET COMPARISON CHART
GATE WARFET Installation Guide
Functions included:
TACTICAL PROGRAMMING CARD
The outstanding Tactical Programming Card provides you with very easy access to the AEG Controller settings. All you need to do is connect the Tactical Programming Card between the battery and the Controller.The card has LED indicators and is lightweight and easy to carry
PRE-COCKING
Victory in the game is often a matter of fractions of seconds. Thanks to the PRE-COCKING, you gain a trigger reaction similar to a real gun. It allows for initial spring compression, which speeds up the trigger response significantly. You can set the time of PRE-COCKING using the Tactical Programming Card. There are two PRE-COCKING MODES:
1) AUTO MODE – the spring is automatically compressed after each shot
2) TRIGGER MODE – the first trigger action compresses the spring, and the second trigger action fires the shot.
Please note: using PRE-COCKING increases wear and tear on the gearbox. PRE-COCKING is designed for SEMI mode. In the AUTO mode, it can result in blank shots.
OPERATING MODES
You can connect the system to a rifle in two ways. Depending on the selected method, you should set a proper operating mode: PlugnPlay or Enhanced (hardwired)
Plug&Play: All you need to do is connect the AEG Control Unit between the battery and the rifle.
Enhanced Hardwired Mode: It requires modification of AEG installation. We connect trigger contacts to WARFET using the signal wire attached to the kit.
PROGRAMMABLE BURST
The burst enables you to shoot a pre-determined number of BBs (1-5 rounds), which is very useful in MILSLIM and when using low-caps. You can transform AUTO MODE to BURST MODE or SEMI MODE to BURST MODE*. The Tactical Programming Card allows you to set the burst time. The AEG Controller automatically corrects the burst time according to the voltage level of the battery.
*SEMI to BURST in modified installations only.
CONFIGURABLE FIRE SELECTOR
The function gives you the option to program your fire selector. There are five operating modes:
- STOCK WIRING SEMI/AUTO
- STOCK WIRING SEMI/BURST
- MODIFIED WIRING SEMI/AUTO
- MODIFIED WIRING SEMI/BURST
- MODIFIED WIRING BURST/AUTO
RATE OF FIRE CONTROL
It enables lossless reduction of the rifle’s rate of fire, so you can use strong LiPo batteries, and still have ROF like in a real gun.
SMART TRIGGER
We know how vital the fast trigger response is during combat. This is why we have developed the Smart Trigger function. It enables you to achieve a faster trigger response. It works with the ROF Control system. During the first shot, the microprocessor sets the ROF Control to 100%. After the first shot, it switches to a previously programmed value (e.g. 50%). As a consequence, the first shot is fired at a full rate of fire, and subsequent shots at a reduced ROF. The best results can be achieved by using a battery with a higher than standard voltage. For example, if you use a 7.4V battery, you can replace it with 11.1V. In this way, you will achieve a faster trigger response with the same rate of fire as with a standard battery. The Smart Trigger is most effective when the Burst time is set at 3 rounds.
BATTERY PROTECTION
Protection against Over-Discharge of the Battery Modern LiPo and LiFe batteries are very sensitive to over-discharge. If you do not want to damage the battery and you care about its service life, this protection is indispensable. The microprocessor monitors the battery voltage constantly. When the voltage drops down to a critical level, the Controller will not allow firing.
SMART FUSE
The new AEG Controller should never let you down on the battlefield. It is the best electronic fuse. The AEG Controller has a true current sensor. A combination of current, voltage and temperature measurements makes your AEG installation highly reliable. If your rifle becomes jammed, the SMART FUSE protects motor and battery against damage. Overheating, overloading or short-circuiting of the electrical system should not damage the Controller.
ACTIVE BRAKE
Do you care about realism? Would you like to increase the life of the gearbox? Does your rifle have such a high rate of fire that you are not able to make a single shot? The Active Brake sorts things out. In SEMI Mode, the brake does not allow for compressing a piston after a shot. The piston will stop in the front position which eliminates unnecessary stresses, increasing the service life of the gearbox and its parts. This is important, especially with an AEG power upgrade. After releasing the trigger, the rifle immediately stops firing. So, you gain more realism and, additionally, you do not waste your precious ammunition.
ON/OFF ACTIVE BRAKE
The Controller provides you with the opportunity to decide if you want to use the Active Brake function. If you do not need this, you can turn it off easily. It will lead to improving the lifespan of your motor.
If you are hot swapping the WARFET from one gun to another, ti is convenient to able to turn off the active braking for guns with weaker motors.
MOSFET
Do you want to achieve a higher rate of fire and faster trigger response? Are you planning a power upgrade of your rifle? In that case, you need a MOSFET.
It targets the energy from the battery directly to the motor, bypassing the mechanical trigger contacts. As a result, you gain a higher rate of fire of the rifle and a faster trigger response, and the contacts are protected against burn out. * Enhanced Hardwired installation required
DEBOUNCING
This provides full compatibility with the micro-switches. It ensures full resistance to contact bounce (vibration). You gain a bigger ROF, a faster trigger response and your MOSFET is less prone to overheating.
BUILT-IN SELF-TEST
It allows you to quickly check whether the AEG Controller works properly. If you have problems with your AEG, the BUILT-IN SELF-TEST allows you to check that the problem is not caused by the Controller.
3RD GENERATION MOSFET
The advent of modern transistors and microcontroller has enabled us to create the smallest and most reliable AEG Controller on the market.
DARK MODE
DARK MODE allows you to turn off the green LED which lights up when a gun is firing. This function is especially useful during night games.
COATING
Thanks to its special conformal coating, it is resistant to atmospheric conditions (Military Specification MIL-V-173C).
14.8V LI-PO READY
The system can be used with batteries up to 14.8V LI-PO. Minimum operating voltage is 3V and maximum voltage is 17V.
MINI TAMIYA READY
Thanks to the Mini Tamiya Adapters included in kit, you will be able to smoothly connect WARFET to your original installation.
PRINTED QUICKSTART
It makes easier starting your adventure with WARFET. The quickstart contains basic information and hints.
Features:
User-friendly configuration via the Tactical Programming Card, plug in between the control unit and battery for programming.
Sturdy and compact AEG Control Unit (Smaller than the MERF 3.2)
Compatibility with the strongest AEG replicas and batteries (ready to work with LiPo 14.8V, 5000 mAh, 60C)
Tested with car batteries
Super-easy installation - thanks to the Mini-Tamiya adapters, you can connect WARFET to the original (stock) wiring
It can work with most built-in MOSFETs
With stock wiring, WARFET reduces melting switch assemblies
In plug 'n play installation,gearbox doesn't need to be opened, just cnnect the control unit and go
In hardwired installation, WARFET draws the energy from the battery directly to the motor, bypassing the mechanical trigger contacts. (hardwired installation is recommended for long-term durability and performance)
Resistant to atmospheric conditions (military coating specifications: MIL-V-173C)
Deep-drain protection for 7.4V, 11.1V, 14.8V LiPoly and 9.6V, 12.8V LiFePO4
Improves battery life, ROF, spring life and gearbox reliability
Included in the kit:
Tactical Programming Card
AEG Control Unit
Battery Mini Tamiya adapter
AEG Mini Tamiya adapter
Pair of Deans-T Connectors
Single Signal Trigger Wire
Duale Signal Trigger Wire
Quickstart Guide
12 Month Manufacturer's warranty against defect and craftsmanship
Professional installation is highly recommended
Warranty does not cover abuse or improper installation
